Actions

WAQ-files: Difference between revisions

From BAWiki

imported>Lang Guenther
(Sicherung)
imported>Lang Guenther
(text added)
Line 32: Line 32:
**:# (REAL SINGLE) mean flow in [m**3/s] for the averaging period.
**:# (REAL SINGLE) mean flow in [m**3/s] for the averaging period.
**: Remark: At the end of the last averaging interval also a record has to be written. Solely the time stamp is used. Data are neglected.
**: Remark: At the end of the last averaging interval also a record has to be written. Solely the time stamp is used. Data are neglected.
** Datei des Typs ''.vol''
** Filetype ''.vol''
**: Wasservolumina in [m**3] für alle NOSEQ Kontrollvolumina, für den jeweiligen Termin.
**: Water volumes in [m**3] for all NOSEQ control volumes.
**: Wasservolumen muss stets >= 0.0 sein.
**: Volume must be >= 0.0.
**: Für jeden Termin:
**: For each record:
**:# (INTEGER) Zeit in Sekunden seit Referenzdatum.
**:# (INTEGER) time in seconds since reference date.
**:# (REAL SINGLE) Wasservolumina in [m**3].
**:# (REAL SINGLE) water volumes in [m**3].
**: Hinweis: Am Ende des letzten Mittelungsintervalls muss ebenfalls ein Record geschrieben werden. Sowohl die Zeitangabe als auch die Daten sind relevant.
**: Remark: At the end of the last averaging interval also a record has to be written. But now time as well as data are of relevance.
** Datei des Typs ''.are''
** Filetype ''.are''
**: Mittlere Durchflussflächen in [m**2] für alle NOQ Austauschflächen.
**: Mean flow area in [m**2] for all NOQ exchanges.
**: Durchflussflächen müssen stets > 0.0 sein.
**: Flow area must always be > 0.0.
**: Für jeden Termin:
**: For each record:
**:# (INTEGER) Zeit in Sekunden seit Referenzdatum.
**:# (INTEGER) time in seconds since reference date.
**:# (REAL SINGLE) Durchflussflächen in [m**2].
**:# (REAL SINGLE) flow area in [m**2].
**: Hinweis: Am Ende des letzten Mittelungsintervalls muss ebenfalls ein Record geschrieben werden. Nur die Zeitangabe wird aus diesem letzen Record verwendet, die Daten selbst werden nicht benutzt.
**: Remark: Identical with ''.flo''.
** Datei des Typs ''.srf''
** Filetype ''.srf''
**: Typische horizontale Flächen in [m**2] für alle NOSEQ Kontrollvolumina.
**: Representative horizontal area in [m**2] for all NOSEQ control volumes.
**: Relevant für die Bestimmung der mittleren Tiefe, den Einfluss von Sedimentation und Erosion, dem Strahlungseinfluss etc.
**: Relevant for the determination of average depth, impact of sedimentation and deposition, solar radiation etc.
**: Für jeden Termin:
**: For each record:
**:# (INTEGER) Zeit in Sekunden seit Referenzdatum.
**:# (INTEGER) time in seconds since reference date.
**:# (REAL SINGLE) horizontale Flächen in [m**2].
**:# (REAL SINGLE) horizontal area in [m**2].
**: Hinweis: Siehe ''.flo'' und ''.are''.
**: Remark: Identical with ''.flo''.
** Datei des Typs ''.len''
** Filetype ''.len''
**: Typischer Abstand im [m] zu den benachbarten Volumina für alle NOQ Austauschflächen.
**: Typical distance in [m] to adjacent control volumes for all NOQ exchanges.
**: Es wird jeweils eine FROM- und eine TO-Distanz benötigt.
**: A FROM as well as a TO distance must be specified.
**: Für den ersten Termin:
**: For the first record:
**:# (INTEGER) Zeit in Sekunden seit Referenzdatum.
**:# (INTEGER) time in seconds since reference date.
**:# (REAL SINGLE) FROM- und TO-Distanzen in [m].
**:# (REAL SINGLE) FROM and TO distances in [m].
**: Hinweis: zeitlich unveränderlich, daher nur ein Mal ausgeben.
**: Remark: no change in time, write only once.
* '''[[CF-NETCDF.NC|cf-netcdf.nc]]
* '''[[CF-NETCDF.NC|cf-netcdf.nc]]
** Datei des Typs ''.nc''
** Filetype ''.nc''
**: Enthält das Gitternetz sowie insbesondere die Aggregations-Tabelle.
**: Grid as well as volume aggregation table.
**: Für weitere Informationen siehe [[NetCDF DelWAQ Daten]].
**: For further informations see [[NetCDF DelWAQ data]].


|nutzerprogramme=[[UNTRIM2]], D-Water Quality [http://www.deltaressystems.com/hydro/product/621497/delft3d-suite Delft Suite]
|nutzerprogramme=[[UNTRIM2]], D-Water Quality [http://www.deltaressystems.com/hydro/product/621497/delft3d-suite Delft Suite]

Revision as of 14:24, 19 July 2012

Basic Information

File-Type

WAQ

File-Form

UNFORMATTED, FORMATTED

Version

Juli 2012

Description-Date

Juli 2012

Significance of the File

coupling files for DelWAQ

File-Contents (in Catchwords)

  • ASCII files
    • Filetype .hyd
      General input data for DelWAQ.
      Example WAQ.hyd (PDF).
    • Filetype .dat
      Description of the open boundary sections where water is exchanged.
      Example WAQ.dat (PDF).
    • Filetype .src
      Description of sources and sinks.
      Example WAQ.src (PDF).
  • Binray files (STREAM, SEQUENTIAL, little endian)
    • Filetype .poi
      All (control) volumes are numbered from 1 to NOSEQ.
      All boundary volumes are numbered from -1 to -NOBND.
      For all NOQ exchange faces (exchanges) the FROM-TO volumes must be specified.
      Four (INTEGER) numbers each: FROM, TO, FROM-1 and TO+1.
      Postive flow is directed FROM nach TO.
      Horizontal exchange face first, vertical exchange faces second.
      In case of 3D layerwise from top to bottom.
    • Filetype .flo
      Fluxes for all NOQ exchange faces (observe FROM-TO). Fluxes are mean flows within the averaging period.
      For each record:
      1. (INTEGER) time in seconds since reference date.
      2. (REAL SINGLE) mean flow in [m**3/s] for the averaging period.
      Remark: At the end of the last averaging interval also a record has to be written. Solely the time stamp is used. Data are neglected.
    • Filetype .vol
      Water volumes in [m**3] for all NOSEQ control volumes.
      Volume must be >= 0.0.
      For each record:
      1. (INTEGER) time in seconds since reference date.
      2. (REAL SINGLE) water volumes in [m**3].
      Remark: At the end of the last averaging interval also a record has to be written. But now time as well as data are of relevance.
    • Filetype .are
      Mean flow area in [m**2] for all NOQ exchanges.
      Flow area must always be > 0.0.
      For each record:
      1. (INTEGER) time in seconds since reference date.
      2. (REAL SINGLE) flow area in [m**2].
      Remark: Identical with .flo.
    • Filetype .srf
      Representative horizontal area in [m**2] for all NOSEQ control volumes.
      Relevant for the determination of average depth, impact of sedimentation and deposition, solar radiation etc.
      For each record:
      1. (INTEGER) time in seconds since reference date.
      2. (REAL SINGLE) horizontal area in [m**2].
      Remark: Identical with .flo.
    • Filetype .len
      Typical distance in [m] to adjacent control volumes for all NOQ exchanges.
      A FROM as well as a TO distance must be specified.
      For the first record:
      1. (INTEGER) time in seconds since reference date.
      2. (REAL SINGLE) FROM and TO distances in [m].
      Remark: no change in time, write only once.
  • cf-netcdf.nc
    • Filetype .nc
      Grid as well as volume aggregation table.
      For further informations see NetCDF DelWAQ data.

Programs using this Type of File

UNTRIM2, D-Water Quality Delft Suite

Example-File

back to: File Descriptions

Overview

Retrieved from "http://wiki.baw.de/en/index.php?title=WAQ-files&oldid=3497"